Effect of ZrO2 paste, surface treatments, and storage on Weibull characteristics and resin bond strength to zirconia

Abstract The objective is to evaluate the effect of different surface treatments and storage on the shear strength of ultratranslucent zirconia. 36 blocks of ultra-translucent zirconia were fabricated (7x7x2mm) and sintered. Then, divided into 12 groups according to the "surface treatment" (C -Primer; Al -Sandblasting with Al2O3 + Primer; Si -Silicate + Primer; Gl -Glaze + HF + Primer; Z -Zirlink; Zp -Zirlink + Primer) and "storage" factors (ST-with 150 days/37º and without). After surface treatment, five cylinders (Ø=2mm; h=2.0mm) of resin cement (n=15) were constructed in each ceramic block; at the end, the shear strength test was performed (1mm/min, 50Kgf), and analysis of surface failures. 60 additional samples (2x2x2mm) were made for extras analysis (surface roughness, MEV, and EDS). Bond strength and surface roughness data were statistically evaluated by ANOVA (2 factors/1 factor), Tukey test (5%), and Weibull analysis, respectively. ANOVA (2-way) revealed that all factors were statistically significant for bond strength. The silicatization groups (SiST: 30.47AMPa; Si: 29.21AMPa) showed the highest bond strength values, regardless of storage (Tukey's test). While the groups treated with Zirlink (ZST: 2.76FMPa; Z: 5.27EFMPa) showed the lowest values, just similar to the GlST group (5.14EFMPa). The Weibull modulus (m) showed a statistical difference between groups (p=0.000). ANOVA (1 factor) revealed that the "surface treatment" factor (p=0.0000) was statistically significant for surface roughness. Therefore, the application of Zirlink and Glaze on pre-sintered zirconia did not promote efficient adhesion of the ultratranslucent zirconia to the resin cement, even when associated with a primer containing MDP.

Resumo O objetivo é avaliar o efeito de diferentes tratamentos superficiais e do envelhecimento na resistência ao cisalhamento da zircônia ultratranslúcida. Foram confeccionados 36 blocos de zircônia ultratranslúcida (7x7x2mm) e sinterizados. Em seguida, divididos em 12 grupos de acordo com o "tratamento de superfície" (C-Primer; Al-Jateamento com Al2O3+Primer; Si-Silicato+Primer; Gl -Glaze+HF+Primer; Z-Zirlink; Zp-Zirlink+Primer) e fatores de "armazenamento" (ST-com, 150 dias/37º e sem). Após o tratamento superficial, foram construídos cinco cilindros (Ø=2mm; h=2,0mm) de cimento resinoso (n=15) em cada bloco cerâmico; ao final foi realizado o ensaio de resistência ao cisalhamento (1mm/min, 50Kgf) e análise de falhas superficiais. Foram confeccionadas 60 amostras adicionais (2x2x2mm) para análises extras (rugosidade superficial, MEV e EDS). Os dados de resistência de união e rugosidade superficial foram avaliados estatisticamente por ANOVA (2 fatores/1fator), teste de Tukey (5%) e análise de Weibull, respectivamente. ANOVA (2 fatores) revelou que todos os fatores foram estatisticamente significativos para a resistência de união. Os grupos de silicatização (SiST: 30,47AMPa; Si: 29,21AMPa) apresentaram os maiores valores de resistência de união, independente do armazenamento (Tukey). Enquanto os grupos tratados com Zirlink (ZST: 2,76FMPa; Z: 5,27EFMPa) apresentaram os valores mais baixos, apenas semelhantes ao grupo GlST (5,14EFMPa). O módulo de Weibull (m) apresentou diferença estatística entre os grupos (p=0,000). A ANOVA (1 fator) revelou que o fator "tratamento superficial" (p=0,0000) foi estatisticamente significativo para rugosidade superficial. Portanto, a aplicação de Zirlink e do Glaze na zircônia pré-sinterizada não promoveu adesão eficiente da zircônia ultratranslúcida ao cimento resinoso, mesmo quando associada a primer contendo MDP.

Bond strength comparison among 10-MDP-containing and non-10-MDP-Containing adhesives in different degrees of dental fluorosis / Comparación de fuerza de unión entre adhesivos que contienen y no contienen 10-MDP en diferentes grados de fluorosis dental

Dental fluorosis can cause changes in the enamel surface, conditioning its functionality and esthetics. The application of dental adhesives is a treatment option; however, their use on fluorotic teeth can result in limitations. The aim of this study was to compare the shear bond strength of two different adhesives, one with 10-MDP and one without 10-MDP, in different degrees of dental fluorosis.This is an in vitro study on dental enamel samples, a total of 180 samples with the inclusion criteria were treated, randomly divided into two groups of 90, according to the type of dental adhesive, where each group was again divided into three groups of 30 samples, representing different degrees of dental fluorosis according to the Thylstrup-Fejerskov index (Group I: TF1 and TF2; Group II: TF3; Group III: TF4). Normality tests, two-factor ANOVA, and post-hoc tests were used to determine differences between the groups, with a significance level of 95%. As results, a statistically significant difference was shown between the use of dental adhesive with 10-MDP and the three groups of dental fluorosis (p=0.011), in addition, a Tukey post-hoc test on the groups treated with 10-MDP adhesive revealed a statistically significant difference between group I versus group II, and group I versus group III, (p=<0.05). It is concluded that the use of adhesive systems with 10-MDP presents a better shear bond strength on enamel with dental fluorosis grades I and II in the Thylstrup-Fejerskov index.

La fluorosis dental puede ocasionar cambios en la superficie del esmalte, condicionando su funcionalidad y estética, la aplicación de adhesivos dentales es una opción de tratamiento, sin embargo, su uso en dientes fluoroticos puede resultar en limitaciones. El objetivo de este estudio consistió en comparar la fuerza de adhesión a la cizalladura de dos diferentes adhesivos, uno con 10-MDP y otro sin 10-MDP, en diferentes grados de fluorosis dental. Se trata de un estudio in vitro en muestras de esmalte dental, un total de 180 muestras con los criterios de inclusión fueron tratadas, aleatoriamente divididas en dos grupos de 90, de acuerdo al tipo de adhesivo dental, donde cada grupo fue dividido nuevamente en tres grupos de 30 muestras, representando diferentes grados de fluorosis dental según el índice de Thylstrup- Fejerskov (Grupo I: TF1 y TF2; Grupo II: TF3; Grupo III: TF4). Para determinar diferencias entre los grupos se utilizaron pruebas de normalidad, ANOVA de dos factores, y pruebas post-hoc, con un nivel de significancia de 95%. Como resultados, se mostró una diferencia estadísticamente significativa entre el uso de adhesivo dental con 10- MDP y los tres grupos de fluorosis dental (p=0.011), además, una prueba post hoc de Tukey sobre los grupos tratados con adhesivo 10-MDP revelaron una diferencia estadísticamente significativa entre el grupo I frente al grupo II, y el grupo I frente al grupo III, (p=<0.05) Se concluye que el uso de sistemas adhesivos con 10-MDP presentan una mejor resistencia de adhesión al cizallamiento en esmalte con grados de fluorosis dental I y II en el índice de Thylstrup-Fejerskov

Resistencia de unión al cizallamiento de diferentes agentes de fijación a aleaciones metálicas odontológicas / Shear bond strength of different bonding agents to dental metal alloys

Introducción: La fijación de las restauraciones indirectas es uno de los pasos más importantes, para conseguir una adecuada retención y sellado de la interfase entre el material restaurador y el diente. Objetivo: Evaluar la resistencia de unión al cizallamiento de diferentes agentes de fijación a dos aleaciones metálicas utilizadas en odontología. Métodos: Estudio experimental in vitro. Cien especímenes de aleaciones de metales base, 50 de níquel-cromo y 50 de níquel-cromo-titanio fueron preparados y divididos de manera aleatoria en 5 grupos. Esta división se realizó acorde con el agente de fijación utilizado: sistema autograbante de dos pasos (Clearfil SE Bond; CSB), sistema adhesivo universal (Single Bond Universal; SBU), cemento resinoso autoadhesivo (Maxcem Elite; ME), ionómero de vidrio (IV) y fosfato de zinc (ZnPO). Posteriormente a la aplicación de cada agente de fijación, los especímenes tratados fueron almacenados en agua destilada por 24 h a 37 ºC y sometidos a un ensayo de resistencia de unión al cizallamiento. Resultados: La resistencia de unión al cizallamiento fue influenciada significativamente por el tipo de agente de fijación (p = 0,002) y el tipo de aleación utilizada (p < 0,001). La resistencia de unión al cizallamiento fue mayor, al utilizar el sistema Clearfil SE Bond, seguida de Single Bond Universal; las diferencias entre Maxcem Elite y el Fosfato de zinc no fueron significativas. Finalmente, el IV no mostró adhesión a ninguna de las aleaciones metálicas utilizadas. Conclusiones: El uso de Clearfil SE Bond aumentó la resistencia de unión de los cementos resinosos a las aleaciones metálicas(AU)

Introduction: The bonding of indirect restorations is one of the most important steps, in order to achieve adequate retention and sealing of the interface between the restorative material and the tooth. Objective: To evaluate the shear bond strength of different bonding agents to two metal alloys used in dentistry. Methods: In vitro experimental study. One hundred specimens of base metal alloys, 50 nickel-chromium and 50 nickel-chromium-titanium were prepared and randomly divided into 5 groups. This division was made according to the bonding agent used: two-step self-etching system (Clearfil SE Bond; CSB), universal adhesive system (Single Bond Universal; SBU), self-adhesive resin cement (Maxcem Elite; ME), glass ionomer (IV) and zinc phosphate (ZnPO). After the application of each bonding agent, the treated specimens were stored in distilled water for 24 hr at 37 ºC and subjected to a shear bond strength test. Results: Shear bond strength was significantly influenced by the type of bonding agent (p = 0.002) and the type of alloy used (p < 0.001). Shear bond strength was highest when using the Clearfil SE Bond system, followed by Single Bond Universal; the differences between Maxcem Elite and Zinc Phosphate were not significant. Finally, IV did not show adhesion to any of the metal alloys used. Conclusions: The use of Clearfil SE Bond increased the bond strength of resinous cements to metallic alloys(AU)

Interplay between resin cements and surface-treated Poly-Ether-Ether-Ketone (PEEK): effect of aging

Aim: This study assessed the effect of thermal aging on the interfacial strength of resin cements to surface-treated PEEK. Methods: Ninety-six PEEK blocks were allocated into 4 groups (n=24), according to following surface treatments: SB - sandblasting with aluminum oxide; SA - acid etched with 98% sulfuric acid; CA ­ coupling agent (Visio.link, Bredent) and CO - control group (untreated). Surface roughness (Ra) was measured and one cylinder (1-mm diameter and height) of Rely-X Ultimate - ULT (3M/ESPE) and another one of Panavia V5 - PAN (Kuraray) were constructed on the treated or untreated PEEK surfaces. Half of the samples of each group were thermal aged (1,000 cycles). Samples were tested at a crosshead speed of 1 mm/min in shear mode (µSBS). Ra and µSBS data were compared using one- and three-way ANOVA, respectively, and Tukey's tests. Results: SA and SB samples had the roughest surfaces, while CA the smoother (p<0.001). Thermal aging reduced µSBS regardless the surface treatment and resin cement used. There was interaction between surface treatment and resin cement (p <0.001), with ULT showing higher µSBS values than PAN. SA provided higher µSBS than SB for both resin cements, while for CA µSBS was higher (PAN) or lower than SB (ULT). Conclusion: Aging inadvertently reduces interfacial strength between PEEK and the resin cements. If ULT is the resin cement of choice, reliable interfacial strength is reached after any PEEK surface treatment. However, if PAN is going to be used only SA and CA are recommended as PEEK treatment

Do irrigation solutions used during root canal instrumentation influence the adhesion of glass fiber posts? A systematic review / As soluções de irrigação usadas durante a instrumentação do canal radicular influenciam a adesão de pinos de fibra de vidro? Uma revisão sistemática

Statement of problem: the bond strength between adhesive cement and root dentin can be affected by irrigation protocols. Purpose: therefore, the objective of this systematic review was to answer the following question: Do irrigation solutions used during root canal instrumentation influence the adhesion of glass fiber posts to root dentin? Material and Methods: this study followed the recommendations of PRISMA 2020 for writing. PubMed, Scopus, Web of Science, and LILACS databases were searched for articles published until 26 January, 2022. Grey literature and a manual search were also performed. The inclusion criteria were based on the PICO strategy: permanent human or animal teeth (P), which were irrigated during root canal instrumentation with endodontic substances (I) and compared to irrigation with sodium hypochlorite at various concentrations (C) to analyze the bond strength of glass fiber posts (O). Two authors independently performed data extraction and the risk of bias. Results: eight articles were included. Four articles were classified as having a high risk of bias, where the others as medium risk. Studies have reported conflicting results regarding the influence of irrigating solutions and the different concentrations of sodium hypochlorite on the adhesion of glass fiber posts to root dentin. Conclusion: the heterogeneity between studies did not allow the conclusion of a true estimate regarding this topic, and further well-designed studies are needed to clarify this issue. Register: CRD42020221835. (AU)

Definição do problema: a resistência de união entre o cimento adesivo e a dentina radicular pode ser afetada pelos protocolos de irrigação. Objetivo: portanto, o objetivo desta revisão sistemática foi responder à seguinte questão: As soluções de irrigação usadas durante a instrumentação do canal radicular influenciam a adesão de pinos de fibra de vidro à dentina radicular? Material e Métodos: este estudo seguiu as recomendações do PRISMA 2020 para sua redação. As bases de dados PubMed, Scopus, Web of Science e LILACS foram pesquisadas para artigos publicados até 26 de janeiro de 2022. A literatura cinza e uma pesquisa manual também foram realizadas. Os critérios de inclusão foram baseados na estratégia PICO: dentes humanos ou animais permanentes (P), que foram irrigados durante a instrumentação do canal radicular com substâncias endodônticas (I) e comparados à irrigação com hipoclorito de sódio em várias concentrações (C) para analisar a resistência de união de pinos de fibra de vidro (O). Dois autores realizaram independentemente a extração de dados e o risco de viés. Resultados:oito artigos foram incluídos. Quatro artigos foram classificados como de alto riscode viés, enquanto os demais como de médio risco. Estudos relataram resultados conflitantes sobre a influência de soluções irrigadoras e as diferentes concentrações de hipoclorito de sódio na adesão de pinos de fibra de vidro à dentina radicular. Conclusão: a heterogeneidade entre os estudos não permitiu a conclusão de uma estimativa verdadeira sobre este tópico, sendo necessários mais estudos bem delineados para esclarecer esta questão. Registo: CRD42020221835 (AU)

Comparison of shear bond strength and color reproduction of two different high-performance polymers veneered with two different thicknesses of resin composite: an in-vitro study / Comparação da resistência ao cisalhamento e reprodução de cor de dois diferentes polímeros de alto desempenho revestidos com duas diferentes espessuras de resina composta: um estudo in vitro

Objective: to evaluate the effect of material type and veneer thickness on the final color and shear bond strength of PEEK bilayered restorations. Material and Methods: sixty-four square-shaped core specimens (7×7×2), were fabricated by CAD/CAM technology from two high-strength polymers, BioHPP (High-Performance Polymer, group B n=32), and Pekkton® ivory (PolyEtherKetoneKetone, group P n=32) then were veneered with resin composite (crea.lign dentin A3). Specimens from each group were divided (n=16) according to the veneer layer thickness (0.5 & 1 mm), then according to the test applied (n=8), either ΔE or shear bond strength (SBS). Specimen surfaces were treated according to the manufacturer's instructions. Specimens were veneered according to the manufacturer's instructions.The mode of failure was evaluated under a stereomicroscope at 40 x magnification after the shear bond strength test. Results: data showed parametric distribution and variance homogeneity and were analyzed using two-way ANOVA. The significance level was set at p<0.05 for all tests. Statistical analysis was performed with the R statistical analysis software version 4.3.1.Results of two-way ANOVA showed that material types and veneer thicknesses had an individual significant effect on the color change. For the shear bond strength, only the sample thickness (1mm) had a significant effect (p=0.033). The majority of samples in different groups presented a mixed failure mode with all the differences being not statistically significant (p>0.05). Conclusion: the thickness of the resin composite veneer can significantly affect the final esthetic outcome and shear bond strength of a bilayered restoration.(AU)

Objetivo: avaliar o efeito do tipo de material e da espessura do revestimento na cor final e na resistência ao cisalhamento de restaurações em duas camadas de PEEK. Material e Métodos: foram fabricados 64 espécimes com núcleo de formato quadrado (7x7x2) usando tecnologia CAD/CAM a partir de dois polímeros de alta resistência, BioHPP (Polímero de Alto Desempenho, grupo B n=32) e Pekkton ivory (Polieterecetona cetona, grupo P n=32), que foram então revestidos com resina composta (crea.lign dentin A3). Os espécimes de cada grupo foram divididos (n=16) de acordo com a espessura do revestimento (0,5 e 1 mm), e depois de acordo com o teste aplicado (n=8), seja ΔE ou resistência ao cisalhamento (SBS). As superfícies dos espécimes foram tratadas de acordo com as instruções do fabricante. Os espécimes foram revestidos de acordo com as instruções do fabricante. O modo de falha foi avaliado sob um estereomicroscópio com ampliação de 40x após o teste de resistência ao cisalhamento. Resultados: os dados apresentaram distribuição paramétrica e homogeneidade de variância e foram analisados por ANOVA de duas vias. O nível de significância foi estabelecido em p<0,05 para todos os testes. A análise estatística foi realizada com o software de análise estatística R, versão 4.3.1. Os resultados da ANOVA de duas vias mostraram que os tipos de materiais e as espessuras do revestimento tiveram um efeito significativo individual na mudança de cor. Para a resistência ao cisalhamento, apenas a espessura da amostra (1mm) teve um efeito significativo (p=0,033). A maioria das amostras em diferentes grupos apresentou um modo de falha misto, com todas as diferenças não sendo estatisticamente significativas (p>0,05). Conclusão:a espessura do revestimento de resina composta pode afetar significativamente o resultado estético final e a resistência ao cisalhamento de uma restauração em duas camadas.(AU)

Effect of adhesive primer application on shear bond strength of self-adhesive cement to tooth structure and two different CAD/CAM milled blocks / Efeito da aplicação do primer adesivo na resistência ao cisalhamento do cimento autoadesivo à estrutura dentária e a dois diferentes blocos fresados CAD/CAM

Objective: This study was conducted to evaluate the influence of the G-CEM ONE adhesive enhancing primer on the shear bond strength of self-adhesive resin cement (G-CEM ONE) to both tooth structure and two different CAD/CAM blocks (GC Initial LiSi and Cerasmart 270). Material and Methods: Forty specimens (cylindrical-shaped, 5 mm in diameter and height) were milled from both CAD/CAM blocks (20 specimens from each block type). Forty sound upper premolars were sectioned to the level of peripheral dentin, then randomly divided into four groups (n = 10): A1: GC Initial LiSi without adhesive enhancing primer; B1: Cerasmart 270 without adhesive enhancing primer; A2: GC Initial LiSi with adhesive enhancing primer; B2: Cerasmart 270 group with adhesive enhancing primer application. The CAD/CAM blocks were cemented on teeth using a self-adhesive resin cement (G-cem one). The shear bond strength was assessed using a computerized universal testing machine. A digital microscope was used to study the mode of failure. The shear bond strength values data were analyzed statistically using paired t-test and independent t-test at the significance level of (0.05). Results: A significant difference was shown in the shear bond strength values among groups (P =0.000). The highest shear bond strength value was revealed in group A2, while group B1 exhibited the lowest shear bond strength value. Conclusion: Using the adhesive enhancing primer on the tooth's surface improved the resin cement's bond strength to CAD/CAM blocks. Additionally, GC Initial LiSi exhibited higher bond strength than Cerasmart 270, with or without the primer (AU)

Objetivo: Este estudo foi conduzido para avaliar a influência do primer adesivo G-CEM ONE na resistência ao cisalhamento do cimento resinoso autoadesivo (G-CEM ONE) tanto na estrutura dentária quanto em dois diferentes blocos CAD/CAM (GC Initial LiSi e Cerasmart 270). Material e Métodos: Quarenta corpos de prova (formato cilíndrico, 5 mm de diâmetro e altura) foram fresados em blocos CAD/CAM (20 corpos de prova de cada tipo de bloco). Quarenta pré-molares superiores sadios foram seccionados até o nível da dentina mais externa e, em seguida, divididos aleatoriamente em quatro grupos (n = 10): A1: GC Initial LiSi sem primer adesivo; B1: Cerasmart 270 sem primer adesivo; A2: GC Initial LiSi com primer adesivo; B2: Grupo Cerasmart 270 com aplicação de primer adesivo. Os blocos CAD/CAM foram cimentados nos dentes com cimento resinoso autoadesivo (G-CEM ONE). A resistência ao cisalhamento foi avaliada utilizando uma máquina de ensaios universal computadorizada. Um microscópio digital foi utilizado para estudar o modo de falha. Os dados dos valores de resistência ao cisalhamento foram analisados estatisticamente por meio do teste t pareado e teste t independente ao nível de significância de (0,05). Resultados: Foi demonstrada diferença significativa nos valores de resistência ao cisalhamento entre os grupos (P =0,000). O maior valor de resistência ao cisalhamento foi revelado no grupo A2, enquanto o grupo B1 exibiu o menor valor de resistência ao cisalhamento. Conclusão:A utilização do primer adesivo na superfície dentária melhorou a resistência de união do cimento resinoso aos blocos CAD/CAM. Além disso, o GC Initial LiSi apresentou maior resistência de união que o Cerasmart 270, com ou sem primer.(AU)

The efficiency of ErCr: YSGG laser on the debonding of different thicknesses of ceramic veneers

Aims: To verify the efficacy of Er,Cr:YSGG laser for debonding of lithium disilicate (LD) reinforced glass ceramic veneers of different thicknesses. Methods: Forty bovine teeth were prepared and randomly divided into four groups (n=10/group) according to the ceramic disc thickness: C0.5 (Control group) and L0.5 (Laser irradiated group) in which LD discs had a thickness of 0.5mm and 5mm diameter; C1 and L1 in which LD discs had a thickness of 1mm and 5mm diameter. The lithium disilcate discs (IPS E.max®, shade HTA2) were fabricated following the manufacturer's recommendations and cemented to the prepared tooth surface. The Er,Cr:YSGG laser was applied to the laser groups at 2.5W and 25Hz for 60seconds. Universal testing machine was used to evaluate the shear bond strength for all samples at a cross head speed of 1mm/min in an inciso-gingival direction parallel to the sample surface. After debonding, the samples were examined under stereoscope to evaluate the mode of failure according to the adhesive remnant index (ARI). Results: Laser irradiation significantly diminishes the shear bond strength from 10.868 MPa to 3.778 MPa for C0.5 and L0.5 groups respectively (p=0.00) and from 14.711 MPa to 4.992 MPa for C1 and L1 groups respectively (p=0.00). The shear bond strength required for debonding increased with increasing thickness of discs, but without significant difference (p=0.110). Higher ARI scores were seen in the laser groups (more cement remaining adhered to the tooth) when compared to the control groups. Conclusions: The Er,Cr:YSGG laser could be an effective and useful tool in debonding of lithium disilicate ceramic veneers as it decreases the shear bond strength required for veneer debonding

Influence of ceramic primers on microshear bond strength to zirconia

This study aimed to investigate the effect of two ceramic primers on the microshear bond strength (µSBS) of yttria-stabilized zirconia (Y-TZP) to two types of self-adhesive resin cement and one BisGMA-based resin cement. Zirconia specimens were sandblasted with 27-µm aluminum oxide and composite cylinders were cemented with resin cement with or without the prior use of ceramic primers. Nine groups (n=12) were randomly distributed according to the cement (self-adhesive RelyX U200/3M ESPE, self-adhesive Maxcem Elite/Kerr, and BisGMA-based dual-cure RelyX ARC/3M ESPE) and ceramic primer (Z-Primer Plus/Bisco and Porcelain Liner M/Sun Medical Co.). After luting, the specimens were stored in distilled water at 37°C for 24 hours and then submitted to the µSBS test. The data were analyzed with two-way ANOVA followed by the Scheffe post hoc test (p<0.05). There were significant differences between RelyX U200 and other groups. There were also significant differences between the RelyX U200 group without ceramic primer and other groups without ceramic primers (p<0.05). Self-adhesive resin cement (RelyX U200 and MaxCem) presented higher microshear bond strength (6.17 and 2.32 MPa) than the conventional resin cement (RelyX ARC) when a porcelain primer was not used (0.43 MPa). When using Porcelain Liner M, the results of RelyX ARC (2.94 MPa) were equivalent to the results of self-adhesive cement (3.93 and 2.11 MPa). When using Z-Prime Plus, the results of MaxCem (5.36 MPa) were lower than those of RelyX U200 (9.59 MPa) but equivalent to those of RelyX ARC (6.07 MPa). When using the RelyX ARC, the use of both ceramic primers improved bond strength to zirconia. When using self-adhesive resin cement, Z-Prime Plus improved microshear bond strength values. It can be concluded that, after 24 hours, the highest µSBS results were obtained when using Z-Prime Plus and RelyX U200 self-adhesive cement.

Effect of cigarette smoke on aesthetic brackets: an in vitro study

ABSTRACT Objective: The objective of this study was to evaluate the effect of cigarette smoke (CS) on physical and mechanical properties of ceramic, polycarbonate and alumina ceramic brackets. The null hypothesis tested was that aesthetic brackets would not be influenced by CS. Methods: Ninety aesthetic brackets were allocated to three groups (n = 30): ceramic (GCE), polycarbonate (GCO) and alumina ceramic (GPS). Ten samples of each group were assigned to color and surface roughness analysis, performed before (T0) and after (T1) exposure to CS; and twenty samples were allocated into control and experimental groups (n = 10) (not exposed and exposed to CS, respectively) for shear bond strength test (SBS). Exposure to CS followed an adaptation of the method described by Le Mesurier. Colorimetric reading, surface morphology and roughness, SBS and adhesive remnant index (ARI) were assessed. Statistical analysis comprised independent and paired t-tests, ANOVA/Tukey and Fisher's exact tests (α = 0.05). Results: Changes were observed in brackets' color (NBS: GCE = 2.4; GCO = 1.9; GPS = 2.1), surface roughness (ΔRa: GCE = 1.1 ± 0.8 µm; GCO = 1.9 ± 1.5µm; GPS = -0.3 ± 0.1 µm / ΔRz: GCE = 1.4 ± 1.0 nm; GPS = -0.5 ± 0.1 nm); and SBS (GPS - experimental = 221.8 ± 48.6 N) after exposure to CS (p< 0.05). Conclusions: Exposure, in vitro, of aesthetic brackets to CS resulted in changes of color to darker and more opaque shades, surface roughness alterations, and higher SBS values. ARI scores were not associated with exposure to CS.

RESUMO Objetivo: O objetivo do presente estudo foi avaliar os efeitos da fumaça do cigarro (FC) nas propriedades físicas e mecânicas de braquetes cerâmicos, de policarbonato e de cerâmica de alumina. A hipótese nula testada foi de que os braquetes estéticos não seriam influenciados pela FC. Métodos: Noventa braquetes estéticos foram alocados em três grupos (n = 30): cerâmica (GCE), policarbonato (GCO) e cerâmica de alumina (GPS). Dez amostras de cada grupo foram designadas para análise de cor e rugosidade superficial, realizada antes (T0) e após (T1) exposição à FC, e vinte amostras foram alocadas nos grupos controle e experimental (n = 10) (não expostos e expostos à FC, respectivamente) para o teste de resistência ao cisalhamento (RC). A exposição à FC foi realizada de acordo com o método descrito por Le Mesurier. Leitura colorimétrica, morfologia e rugosidade de superfície, RC e índice de adesivo remanescente (ARI) foram avaliados. A análise estatística foi realizada por meio dos testes t independente e para amostras pareadas, ANOVA/Tukey e teste exato de Fisher (α = 0,05). Resultados: Foram observadas alterações na cor (NBS: GCE = 2,4; GCO = 1,9; GPS = 2,1), rugosidade superficial (ΔRa: GCE = 1,1 ± 0,8 µm; GCO = 1,9 ± 1,5 µm; GPS = -0,3 ± 0,1 µm / ΔRz: GCE = 1,4 ± 1,0 nm; GPS = -0,5 ± 0,1 nm) e RC (GPS - experimental = 221,8 ± 48,6 N) dos braquetes após exposição à FC (p< 0,05). Conclusões: A exposição in vitro de braquetes estéticos à FC resultou em mudanças na cor, para tons mais escuros e mais opacos; alterações na rugosidade superficial e maiores valores de RC. Os resultados do ARI não foram associados à exposição à FC.

Evaluation of antibacterial properties and shear bond strength of orthodontic composites containing silver nanoparticles, titanium dioxide nanoparticles and fluoride: An in vitro study

ABSTRACT Objective: The study aimed at determining the antibacterial properties of composites containing silver nanoparticles (Ag NPs) or titanium dioxide nanoparticles (TiO2 NPs), and a fluoride-releasing composite against Streptococcus mutans and Lactobacillus acidophilus, and to evaluate the effect on shear bond strength (SBS) of nanoparticles-modified composites. Materials and Methods: An orthodontic composite was modified by adding 1% w/w Ag NPs or 1% w/w TiO2 NPs. Composite discs were prepared to evaluate the antibacterial properties of these modified composites against Streptococcus mutans and Lactobacillus acidophilus, using three different antibacterial tests, namely: Disk agar diffusion test, Biofilm inhibition test and eluted component test. For evaluating the shear bond strength, 80 extracted premolars were collected and divided into four groups (n=20 each), which were bonded with stainless steel preadjusted Edgewise brackets, by using these modified composites. Their SBS was then compared with that of the control group, using a universal testing machine. Results: Composite discs containing nanoparticles and fluoride were capable of producing growth inhibition zones for all bacterial types. Results of the biofilm inhibition test showed that all the study groups inhibited the bacterial count, in comparison to the control group. A significant difference of SBS was observed between all groups. Conclusion: The antibacterial activity of orthodontic composites modified with Ag and TiO2 nanoparticles was significant, compared with conventional and fluoride-containing composites. The control group showed the highest SBS, followed by fluoride, titanium, and silver groups, with statistically significant difference in mean SBS values among all groups.

RESUMO Objetivo: O objetivo do presente estudo foi determinar a eficácia das propriedades antibacterianas de compósitos contendo nanopartículas de prata (Ag NPs) ou nanopartículas de dióxido de titânio (TiO2 NPs) e de um compósito com liberação de flúor, contra as bactérias Streptococcus mutans e Lactobacillus acidophilus e, também, avaliar o efeito na resistência ao cisalhamento (RC) desses compósitos modificados com nanopartículas. Métodos: Os compósitos ortodônticos foram modificados pela adição de 1% p/p de Ag NPs e 1% p/p de TiO2 NPs. Discos de compósito foram preparados para avaliar as propriedades antibacterianas desses grupos contra as bactérias Streptococcus mutans e Lactobacillus acidophilus, usando três testes antibacterianos diferentes: teste de disco-difusão em ágar, teste de inibição da formação de biofilme e teste de componentes eluídos. Para avaliar a resistência ao cisalhamento dos compósitos, 80 pré-molares extraídos foram coletados e divididos em quatro grupos, contendo 20 dentes cada. Foram utilizados braquetes Edgewise pré-ajustados de aço inoxidável para colagem nos dentes usando as resinas modificadas. A RC desses compósitos modificados foi comparada à dos grupos controle, usando uma máquina universal de testes. Resultados: Os discos de compósito contendo as nanopartículas e flúor foram capazes de produzir halos de inibição de crescimento para todos os tipos de bactérias. Os resultados do teste de inibição do biofilme mostraram que houve uma redução na contagem de bactérias em relação ao grupo controle. Diferenças significativas na RC foram observadas entre todos os grupos. Conclusão: A atividade antibacteriana dos compósitos ortodônticos modificados com nanopartículas de Ag e TiO2 foi significativa, quando comparada ao compósito convencional e ao compósito com flúor. O grupo controle apresentou a maior RC, seguido pelos grupos Flúor, Titânio e Prata, com diferença estatisticamente significativa nos valores médios da RC entre todos os grupos.

Effects of ionizing radiation and different resin composites on shear strength of ceramic brackets: an in vitro study

ABSTRACT Introduction: Head and neck cancer is considered one of the most common types, and its treatment includes radiotherapy, which can trigger side effects and undesirable sequelae in the oral cavity and dental tissues. Objective: This study aimed to make an in vitro evaluation of the shear strength and failure mode of ceramic orthodontic brackets bonded with two different composites in enamel submitted to ionizing radiation. Methods: After the study was approved by the Research Ethics Committee, 60 healthy human premolars were selected and divided into two groups, based on the absence or presence of ionizing irradiation of the enamel. The fragments were thermocycled and then randomly subdivided into two subgroups, according to the composite used for bonding the ceramic brackets (Inspire Ice - Ormco) to the enamel (n = 15): Transbond XT composite (3M), and Light Bond composite (Reliance). After 24 hours, the specimens were submitted to the shear strength test, and the failure mode was analyzed using a stereomicroscope and confocal microscopy. The shear strength data were submitted to two-way ANOVA, considering a significance level of 5%. Results: The groups submitted to radiation presented lower shear strength values (4.48MPa) than those not irradiated (9.23MPa) (p< 0.001), and the tested composites were not statistically different (p= 0.078). Regarding the fracture mode, all the groups presented mostly adhesive fractures. Conclusion: It was concluded that ionizing radiation negatively affects the adhesion of ceramic brackets, regardless of the composite used for bonding.

Effect of Saliva/Blood Contamination on Enamel Bond Strength / Efeito da Contaminação de Saliva/Sangue na Força de União ao Esmalte

Abstract In the routine clinical situation, the contamination by blood and/or saliva in restorative procedures can be happen in non-cooperation of the patient in dental office. The aim of the study was to assess in vitro shear bond strength of a resin sealant associated with two types of adhesives contaminated with saliva and blood. Healthy human molars were used and the specimens and the crowns were sectioned in the bucco-lingual direction, thus obtaining two segments of similar proportions (mesial and distal), totaling 60 surfaces, and the surfaces were randomly divided into 4 groups (n = 15). Group I (control) received no type of contamination and the sealant was applied. In group II, the surfaces were contaminated with 10 µl of saliva/blood and the sealant was applied. In group III, the surfaces were contaminated with 10 µl of saliva/blood and the Single Bond total-etch adhesive system was applied followed by application of sealant. In group IV, the surfaces were contaminated with 10 µl of saliva/blood and the Prime & Bond NT total-etch adhesive system was applied followed by the application of sealant. Samples were tested in the universal testing machine and the analysis of shear bond strength was performed. A difference between Group I (12.61MPa) and the other groups was found; Group II (2. 28MPa) was different than Groups III (7.07MPa) and IV (7.79MPa), but Groups III and IV were similar. The application of an adhesive system when there is contamination with saliva/blood is required prior to application of pit and fissure sealants. (AU)

Resumo Na situação clínica de rotina, a contaminação por sangue e/ou saliva em procedimentos restauradores pode ocorrer em pacientes que não colaboram no consultório odontológico. O objetivo do estudo foi avaliar a resistência ao cisalhamento in vitro de um selante de resina associado a dois tipos de adesivos contaminados com saliva e sangue. Foram utilizados molares humanos saudáveis e os espécimes e as coroas foram seccionados na direção bucal-lingual, obtendo assim dois segmentos de proporções semelhantes (mesial e distal), totalizando 60 superfícies, e as superfícies foram divididas aleatoriamente em 4 grupos (n = 15). O Grupo I (controle) não recebeu nenhum tipo de contaminação e o selante foi aplicado. No grupo II, as superfícies foram contaminadas com 10 µl de saliva / sangue e o selante foi aplicado. No grupo III, as superfícies foram contaminadas com 10 µl de saliva / sangue e o sistema adesivo Single-Bond foi aplicado seguindo a aplicação de selante. No grupo IV, as superfícies foram contaminadas com 10 µl de saliva / sangue e o sistema adesivo de ataque total Prime & Bond NT foi aplicado seguido da aplicação de vedante. As amostras foram testadas na máquina de ensaio universal e a análise da resistência à ligação ao cisalhamento foi realizada. Uma diferença entre o Grupo I (12,61MPa) e os outros grupos foi encontrada; O Grupo II (2,28 MPa) foi diferente dos Grupos III (7,07MPa) e IV (7,79 MPa), mas os Grupos III e IV foram semelhantes. A aplicação de um sistema adesivo quando existe contaminação com saliva / sangue é necessária antes da aplicação de selantes de fissura e fissura.

Bond strength of resin composite to enamel submitted to at-home desensitizer and bleaching agents

Aim: This study evaluated the effect of a desensitizer agent (DES) during bleaching with 10% carbamide peroxide (CP) on enamel microshear bond strength (µSBS). Methods: Sixty bovine incisors were obtained and randomly distributed into groups (n=15): (C) Control: no desensitizing or bleaching, (DES) desensitizing gel application, (CP) bleaching with 10% CP and (CP/DES) bleaching with 10% CP combined with DES. Bleaching was performed for 6 h/day for 14 consecutive days. DES was applied for 8 h only on the 7th and 14th days of therapy. Specimens were stored in artificial saliva among the CP or DES applications and submitted to µSBS testing at three postrestoration times (n=5): 24 h, 7 days, and 14 days after bleaching using a universal testing machine. Failure modes were observed under a stereomicroscope. Data were analyzed by two-way ANOVA and Tukey's test (α=5%). Results: Immediately after bleaching (24 h), CP promoted lower µSBS than the C and DES groups (p<0.05) but with no differences from the CP/DES. µSBS increased in the DES, CP, and CP/DES groups (p<0.05) when bonding was performed for 7 or 14 days elapsed from bleaching. CP/DES exhibited the highest µSBS among the groups 14 days after bleaching (p<0.05). Cohesive failure in enamel was predominant in the CP groups, while adhesive failure was mostly observed for the other groups. Conclusion: The use of a desensitizer during at-home bleaching maintained the enamel immediate bond strength, and its application favored bonding when the restoration was delayed for 14 days

Is the Er:YAG laser affect the surface characteristics and bond strength of Y-TZP?

Abstract This study evaluated the surface characteristics and bond strength of Y-TZP treated with Er:YAG laser at different focal distances. 120 Y-TZP blocks were divided into five groups (n=24), according to the surface treatment: no treatment (C-); sandblasting with silica-coated aluminum oxide particles (C+); and Er:YAG laser application at focal distances of 1mm (Er:YAG-1), 4mm (Er:YAG-4), and 7mm (Er:YAG-7). Surface characteristics were analyzed using Vickers microhardness, confocal laser microscope, scanning electron microscopy (SEM), and X-ray diffractometer (XRD). For the bond strength test, 100 Y-TZP blocks were subdivided into two subgroups (n=10), according to the resin cement used: with (MDP+) or without 10-methacryloyloxydecyl dihydrogen phosphate (MDP-). The Vickers microhardness and surface roughness were analyzed by one-way ANOVA and bond strength by two-way ANOVA and Tukey's test for both (α=0.05). Vickers microhardness differences were not observed between the groups (p>0.05); C+ showed higher surface roughness values. SEM images showed micromorphological differences between the groups. The XRD data detected tetragonal crystals for C- and, for the other groups, tetragonal and monoclinic peaks. For bond strength, no statistically difference significance were observed among the cements with or without MDP (p>0.05) but showed significant difference between the surface treatments (C+ > C- = Er:YAG1 > Er:YAG4 = Er:YAG7) (p<0.05). Suggested that the Er:YAG laser cannot replace conventional treatment with aluminum oxide particles and the presence of MDP in the resin cement had no influence on the bond strength.

Resumo Este estudo avaliou as características de superfície e resistência de união de Y-TZP tratado com laser de Er: YAG em diferentes distâncias focais. Cento e vinte blocos de Y-TZP foram divididos em cinco grupos (n=24), de acordo com a superfície de tratamento: sem tratamento (C-); asperização com partículas de óxido de alumínio revestidas por sílica (C +); e aplicação de laser Er: YAG a distâncias focais de 1 mm (Er: YAG-1), 4 mm (Er: YAG-4) e 7 mm (Er: YAG-7). As características de superfície foram analisadas por meio de microdureza Vickers, microscópio confocal a laser, microscopia eletrônica de varredura (MEV) e difratômetro de raios-X (DRX). Para o ensaio de resistência de união, cem blocos de Y-TZP foram subdivididos em 2 subgrupos (n=10) de acordo com o cimento resinoso utilizado (n=12): com 10-metacriloiloxidecil dihidrogenofosfato (MDP+) ou sem (MDP-). Microdureza Vickers e rugosidade de superfície foram analisadas por ANOVA a 1 fator e a resistência de união por ANOVA a 2 fatores e ambos seguidos de teste complementar de Tukey (α=0,05). Não foram observadas diferenças de microdureza Vickers entre os grupos; C+ apresentou maiores valores de rugosidade superficial. Imagens de MEV mostraram diferenças micromorfológicas entre os grupos. Os dados de DRX detectaram apenas cristais tetragonais para C- e, para os outros grupos, picos de zircônia nas fases tetragonal e monoclínica. Para a resistência de união, não foram observadas diferenças estatisticamente significante entre os cimentos com e sem MDP (p>0.05), mas foram observadas diferenças significativas entre os tratamentos de superfície (C+ > C- = Er:YAG1 > Er:YAG4 = Er:YAG7) (p<0.05). Sugere-se que o laser de Er: YAG não pode substituir o tratamento convencional com partículas de óxido de alumínio e a presença de MDP no cimento resinoso não influenciou na resistência de união.

Efeito de diferentes protocolos de colagem de bráquetes cerâmicos com LED de alta potência / Effect of different ceramic bracket bonding protocols with high power LED

OBJETIVO: Avaliar o efeito de diferentes protocolos de fotoativação na resistência de união ao cisalhamento (RUC) de bráquetes cerâmicos colados ao esmalte dentário, nas falhas de união através do índice remanescente adesivo (IRA) e no grau de conversão (GC) de uma resina utilizando o fotoativador de alta potência Valo™ Cordless® (Ultradent) no modo Xtra power (3.200 mW/cm2 ). METODOLOGIA: Os bráquetes foram colados (Transbond XT® , 3M Unitek) em 80 coroas de incisivos bovinos, distribuídas aleatoriamente em dois grupos (N=40): bráquetes monocristalinos (Grupo 1) e bráquetes policristalinos (Grupo 2). Cada grupo foi subdividido em 4 subgrupos (n=10) de acordo com o protocolo de fotoativação: 3 ou 6 segundos no centro; 3s na mesial/3s na distal; e 3s na cervical/3s na incisal. Após armazenamento por 4 meses (água destilada/37°C), realizou-se o ensaio de cisalhamento (100KgF, 1mm/min). Para análise do GC, foram confeccionados 80 discos de resina com os mesmos protocolos de fotoativação utilizados na colagem dos bráquetes. A RUC (MPa) foi avaliada descritivamente, pelo teste T de Student, ANOVA one- e two-way e pelo pós-teste de Tukey. O GC (%) foi avaliado descritivamente, pela ANOVA two-way e pelo pós-teste de Tukey. As falhas de união foram classificadas de acordo com o IRA, analisadas descritivamente e pelo teste de KruskalWallis. RESULTADOS: Em relação à RUC, todos os protocolos do Grupo 2 e apenas o de fotoativação no centro por 3 segundos do Grupo 1 apresentaram valores clinicamente aceitos; os valores foram significativamente afetados (p<0,01) pelo tipo de bráquete; e ao comparar as médias intergrupos correspondentes, observou-se p=0,003 entre os protocolos de 6s no centro e p=0,010 entre os protocolos de 3s na cervical/3s na incisal. Na avaliação do GC, os valores foram afetados de forma estatisticamente significativa pelo protocolo de fotoativação (p=0,002) e pela interação entre os fatores (tipo de bráquete*protocolo de fotoativação; p=0,033). Os escores 4 (39,4%; p>0,05) e 3 (72,5%; p=0,001) do IRA foram predominantes nos Grupos 1 e 2, respectivamente. CONCLUSÃO: Deve-se ter cautela ao realizar a colagem de bráquetes cerâmicos com o Valo™ Cordless® no modo Xtra power, pois observou-se RUCs altas. A RUC e o GC podem apresentar diferenças estatisticamente significativas a depender do tipo de bráquete e do protocolo de fotoativação aplicado. De modo geral, sugere-se utilizar o bráquete policristalino ao monocristalino e aplicar 3 segundos de fotoativação no centro do bráquete (AU).

OBJECTIVE: To evaluate the effect of different photoactivation protocols on shear bond strength (SBS) of ceramic brackets bonded to dental enamel, on bond failure through the adhesive remnant index (ARI) and on the degree of conversion (DC) of a resin using the highpower photo activator Valo™ Cordless® (Ultradent) in Xtra power mode (3.200 mW/cm2 ). METHODOLOGY: The brackets were bonded (Transbond XT® , 3M Unitek) on 80 crowns of bovine incisors, randomly distributed into two study groups (N=40): monocrystalline brackets (Group 1) and polycrystalline brackets (Group 2). Each group was subdivided into 4 subgroups (n=10) according to the photoactivation protocol used: 3 or 6 seconds in the center; 3s in the mesial/3s in the distal; and 3s in the cervical/3s in the incisal. After storage for 4 months (distilled water/37°C), the shear test (100KgF, 1mm/min) was performed. For DC analysis, 80 resin discs were made with the same photoactivation protocols used in bonding brackets. The SBS (MPa) was evaluated descriptively, using Student's T test, ANOVA one- and two-way and by Tukey's post-test. The DC (%) was assessed descriptively, by ANOVA two-way and by Tukey's post-test. Union failures were classified according to the ARI, analyzed descriptively and by Kruskal-Wallis' test. RESULTS: Regarding the SBS, all protocols in Group 2 and only the photoactivation on the center for 3 seconds of Group 1 presented clinically accepted values; the values were significantly affected (p<0.01) by the type of bracket; and when comparing the corresponding intergroup averages, p=0.003 was observed between the protocols of 6s in the center and p=0.010 between the protocols of 3s in the cervical/3s in the incisal. In the DC evaluation, the values were significantly affected by the photoactivation protocol (p=0.002) and by the interaction between the factors (type of bracket*photoactivation protocol; p=0.033). ARI scores 4 (39.4%; p>0.05) and 3 (72.5%; p=0.001) were predominant in Groups 1 and 2, respectively. CONCLUSION: Caution should be exercised when bonding ceramic brackets with Valo™ Cordless® in Xtra power mode, because high SBSs were observed. SBS and DC might present statistically significant differences depending on the type of bracket and the photoactivation protocol applied. In general, it is suggested to use the polycrystalline bracket to the monocrystalline and apply 3 seconds of photoactivation in the center of the bracket (AU).

Effect antioxidants application on microshear bond strength of universal adhesive to bleached enamel / Efeito da aplicação de antioxidantes na resistência de união do adesivo universal ao esmalte clareado

Purpose: To evaluate, in vitro, the influence of antioxidants (green tea extract - GT and sodium ascorbate - SA) on microshear bond strength (µSBS) of a universal adhesive system ­ self-etching mode (UAS) to bleached enamel. Material and Methods: After obtaining 50 fragments of human dental enamel (4 mm x 4 mm), forty fragments were submitted to at-home bleaching technique using 10% carbamide peroxide (Opalescence PF, Ultradent) for two h/day, for four weeks. They were randomly divided in four groups (n = 10): GT - 10% aqueous GT solution (60 min); SA - 10% SA solution (10 min); Negative control - no antioxidant agent, immediately restored; PC1 (positive control 1) - no antioxidant agent, restored 14 days the bleaching procedure. Ten enamel fragments were assigned to PC2 group (positive control 2), in which the adhesive procedures were realized in non-bleached enamel. The UAS (Adper Single Bond Universal, 3M ESPE) was applied on enamel surface according to manufacturer's instructions and two cylinders (0.8 mm diameter) of nanoparticulate composite resin (Z350, 3M ESPE) were made on each sample. After 24 h, the cylinders were submitted to µSBS in a universal test machine (0.5 mm/min). Fracture mode was evaluated in stereomicroscope (30x magnification). SBS data, in MPa, was submitted to one-way ANOVA and fracture mode to Chi-square test (α = 0.05). Results: There was no statistical difference between the experimental groups (p = 0.545) and fracture mode (p = 0.16424). There was predominance of adhesive fracture in all groups. Conclusion: Neither the bleaching procedure nor the application of antioxidants to bleached enamel interfered in the bond strength of the tested universal adhesive system (AU)

Objetivo: Avaliar, in vitro, a influência de antioxidantes (extrato de chá verde - GT e ascorbato de sódio - SA) na resistência de união ao microcisalhamento (µSBS) de um sistema adesivo universal - modo de autocondicionamento (UAS) ao esmalte clareado. Material e Métodos: Realizou-se a obtenção de 50 fragmentos de esmalte dental humano (4 mm x 4 mm), sendo que desses, quarenta fragmentos foram submetidos à técnica de clareamento caseiro utilizando peróxido de carbamida a 10% (Opalescence PF, Ultradent) por duas horas/dia, durante quatro semanas. Eles foram divididos aleatoriamente em quatro grupos (n= 10): Expostos a GT - solução aquosa de GT a 10% (60 min); expostos a SA - solução 10% SA (10 minutos); Sem exposição ao agente antioxidante e imediatamente restaurado - (controle negativo); Sem exposição ao agente antioxidante e restaurado 14 dias após o clareamento - PC1 (controle positivo 1). Os dez fragmentos de esmalte restantes foram atribuídos ao grupo PC2 (controle positivo 2), no qual os procedimentos adesivos foram realizados em esmalte não clareado. O UAS (Adper Single Bond Universal, 3M ESPE) foi aplicado na superfície do esmalte de acordo com as instruções do fabricante e dois cilindros (0,8 mm de diâmetro) de resina composta nanoparticulada (Z350, 3M ESPE) foram feitos em cada amostra. Após 24 h, os cilindros foram submetidos ao µSBS em uma máquina de teste universal (0,5 mm/min). O modulo de fratura foi avaliado em estereomicroscópio (aumento de 30x). Os dados do SBS, em MPa, foram submetidos à ANOVA unidirecional e ao modo fratura ao teste do qui-quadrado (α = 0,05). Resultados: Não houve diferença estatística entre os grupos experimentais (p = 0,545) e modulo de fratura (p = 0,16424). Houve predomínio de fratura adesiva em todos os grupos. Conclusão: Nem o procedimento de clareamento nem a aplicação de antioxidantes no esmalte clareado interferiram na resistência de união do sistema adesivo universal testado. (AU)

Effect of chitosan treatment on shear bond strength of composite to deep dentin using self-etch and total-etch adhesive systems / Efeito do tratamento com quitosana na resistência ao cisalhamento de resina compost em dentina profunda usando sistemas adesivos autocondicionantes e condicionamento total

Objective: To assess the shear bond strength (SBS) of resin composite to deep dentin, using 1 and 2.5% chitosan pretreatment as well as different adhesive systems. Material and Methods: 80 human maxillary molars were randomly divided to eight groups according to the type of adhesive system and dentin pretreatment (n = 10): I) two-step self-etch system (Clearfil SE bond); II) two-step etch-and-rinse system (Adper single bond 2); III) 2.5% chitosan + Clearfil SE bond; IV) 2.5% chitosan +etch + Adper single bond 2; V) etch + 2.5% chitosan + Adper single bond 2; VI) 1% chitosan + Clearfil SE bond; VII) 1% chitosan + etch + Adper single bond 2; VIII) etch + 1% chitosan + Adper single bond 2 (chitosan solution (w/v): 2.5 g and 1 g of chitosan (Sigma Aldrich, USA) was dissolved in 100 ml of 1% acetic acid). Plastic molds were positioned on dentin and filled with composite (Z350, 3M ESPE, USA). SBS (MPa) was tested using a universal testing machine. ANOVA tests, Tukey's test, and independent t test were used to analyze data (p ≤ 0.05). Results: The highest SBS value among self-etch groups was observed with 1% chitosan (p = 0.001). In the etch-and-rinse group, the SBS of 1% chitosan was significantly lower than the other groups. Chitosan treatment following acid etching led to higher SBS in comparison to when chitosan was applied before etching, with the significant difference in 1% concentration (p = 0.030). A predominance of mix fractures was observed in dentin. Conclusion: Improved dentin bond strength can be achieved through immediate dentin pretreatment with 1% chitosan in self-etch adhesive systems. Chitosan Pretreatment may not be advantageous for etch-and-rinse adhesive systems. (AU)

Objetivo: Avaliar a resistência ao cisalhamento (RC) da resina composta em dentina profunda, utilizando quitosana de 1 e 2,5% como pré-tratamento, e também diferentes sistemas adesivos. Materiai e métodos: 80 molares superiores humanos foram divididos aleatoriamente em oito grupos de acordo com o tipo de sistema adesivo e pré-tratamento dentinário (n = 10): I) sistema autocondicionante de dois passos (Clearfil SE bond); II) sistema convencional de dois passos (Adper Single Bond II); III) quitosana 2,5% + Clearfil SE bond; IV) quitosana 2,5% + ácido + Adper single bond; V) ácido + quitosana 2,5% + Adper single bond II; VI) quitosana 1% + Clearfil SE bond; VII) quitosana 1% + ácido + Adper single bond II; VIII) ácido + quitosana 1% + Adper single bond II (solução de quitosana (w/w): 2,5 ge 1 g de quitosana (Sigma Aldrich, EUA) foi dissolvido em 100 ml de ácido acético a 1%). Moldeiras foram posicionados na dentina e preenchidos com resina composta (Z350, 3M ESPE, EUA). O RC (MPa) foi testado em uma máquina de teste universal. Os testes ANOVA, teste de Tukey e teste t foram usados para analisar os dados (p ≤ 0,05). Resultados: O maior valor de RC entre os grupos autocondicionantes foi observado com quitosana a 1% (p = 0,001). No grupo do condicionamento total a RC da quitosana a 1% foi significativamente menor do que nos outros grupos. O tratamento com quitosana após o condicionamento ácido levou a um maior RC em comparação a quitosana aplicada antes do condicionamento, com diferença significativa na concentração de 1% (P = 0,030). Observou-se predomínio de fraturas na dentina. Conclusão: A resistência de união à dentina pode ser alcançada por meio do pré-tratamento imediato da dentina com quitosana a 1% em sistemas adesivos autocondicionantes. O pré-tratamento com quitosana pode não ser vantajoso para sistemas adesivos de condicionamento total. (AU)

Mechanical and bonding properties of different combinations of nanohybrid and bulk-fill composites / Propiedades mecánicas y adhesión entre diferentes combinaciones composite Nanohíbrido-Bulkfill

ABSTRACT The aim of this research was to determine compressive and shear bond strength of blocks prepared with bulk-fill and nanofill composite resin combinations. Materials used were Filtek Bulk Fill (FBF) and Z350 (both 3M-ESPE) and Surefil SDR flow (SFF) - Dentsply. To determine shear bond strength, cylindrical specimens 10 mm thick were prepared with composite consisting of thicknesses of 6 mm of one material and 4 mm of the other, in the following combinations: G1: FBF- FBF; G2: Z350-Z350, G3: FBF-Z350, G4: Z350-SFF and G5: SFFSFF. Materials were cured using a 1100 mw/cm2 light for 20 seconds for each layer. Samples were stored for 24 hours at 37 °C in distilled water and shear bond strength was determined. To assess compressive strength, cylindrical samples 4 mm diameter and 6 mm thick consisting of 4 mm + 2 mm were used in the same combinations as described above, stored in distilled water at 37 °C for 24 hours, after which compressive strength was determined. Both tests were performed with a Universal testing machine at a cross head speed of 1 mm/min. Results were analyzed with ANOVA and Tukey's test. Means and standard deviations in MPa for each group were the following: Shear bond strength: G1: 435.87 (65.86), G2: 233.6 (108.15), G3: 279.2 (22.05), G4:449.1 (109.35) and G5: 196.6 (51.16). Compressive strength: G1:160.07(4.27), G2: 149.49 (14.06), G3: 156.10 (29.99), G4: 199-30(39.28), G5: 171.23 (28.71). Evaluation with ANOVA showed no significant differences among combinations for compressive strength (p>0.05) and significant differences for bond strength (p<0.05). Tukey's test showed three homogeneous groups. Under these experimental conditions, it can be concluded that the study combinations have adequate mechanical behavior, equivalent to materials used individually. However, shear bond strength was affected by the combinations analyzed.

RESUMEN El objetivo de este trabajo fue determinar la resistencia compresiva (RC) y la resistencia adhesiva al corte (RAC) en bloques preparados con combinaciones de composites bulk-fill y nanoparticulados. Los materiales usados fueron Filtek Bulk Fill (FBF) y Z350 (ambos de 3M-ESPE) y Surefil SDR flow (SFF) - Dentsply. Para medir la RAC, se prepararon probetas cilindricas de 10 mm de espesor consistentes en 6 mm de un material y 4 mm del otro con las siguientes combinaciones: G1: FBF- FBF; G2: Z350-Z350, G3: FBF-Z350, G4: Z350-SFF y G5: SFF-SFF. Se curaron a 1100 mw/cm2 durante 20 segundos cada capa. Se conservaron 24 horas a 37 °C en agua destilada antes de determinar la RAC. Para medir la RC se prepararon probetas de 4 mm de diametro y 6 mm de espesor (4 mm + 2 mm de cada material), con las mismas combinaciones. Se conservaron en agua destilada a 37 °C durante 24 horas y se midió la RC. Ambos ensayos se realizaron con una máquina universal para ensayos mecánicos a 1 mm/min de velocidad de desplazamiento de cabezal. Los resultados se evaluaron con ANOVA y prueba de Tukey. Las medias y desviaciones estándar (MPa) para cada grupo fueron: RAC: G1: 435.87 (65.86), G2: 233.6 (108.15), G3: 279.2 (22.05), G4:449.1 (109.35) y G5: 196.6 (51.16). RC: G1:160.07(4.27), G2: 149.49 (14.06), G3: 156.10 (29.99), G4: 199-30(39.28), G5: 171.23 (28.71). ANOVA no mostró diferencias estadísticamente significativas para RC (p>0.05) y diferencias significativas para RAC (p<0.05). La prueba de Tukey mostró tres grupos homogéneos. En las condiciones experimentales de este trabajo puede concluirse que las combinaciones evaluadas tienen un comportamiento mecánico adecuado equivalente al de los materiales individuales. Sin embargo, la adhesión entre materiales se vio afectada por las combinaciones realizadas.

Elastographic analysis of the supraspinatus tendon in different age groups / Análise elastográfica do tendão supra-espinal em diferentes faixas etárias

ABSTRACT Objective: To compare the mechanical properties of the supraspinatus tendon in different age groups using Supersonic Shearwave Imaging (SSI) elastography. Methods: We evaluated 38 healthy individuals of both genders, 20 being in the range of 20 to 35 years and 18 being over 60 years. The shear modulus of the supraspinatus tendon was measured by SSI elastography, always on the right side. Means between age groups were compared and statistically analyzed using the Shapiro-Wilk normality test followed by the student's t-test and were established as a statistically significant value of p ≤ 0.05. Results: A statistically significant difference was observed when the mean values of the shear modulus of the supraspinatus tendon of young adults (23.98 ± 9.94 KpA) were compared with those of older adults (17.92 ± 6.17 KpA). Conclusion: We found a difference between the means of the shear modulus measured by the SSI elastography, showing a significant decrease of the shear modulus with the chronological age progression. Level of Evidence III, Diagnostic Studies - Investigating a Diagnostic Test.

RESUMO Objetivo: Comparar as propriedades mecânicas do tendão supraespinal em diferentes grupos etários, utilizando a elastografia Supersonic Shearwave Imaging (SSI). Métodos: Foram avaliados 38 indivíduos saudáveis de ambos os sexos, sendo 20 na faixa de 20 a 35 anos e 18 acima dos 60 anos de idade. Foi aferido o módulo de cisalhamento do tendão supraespinal por elastografia SSI, sempre do lado direito. As médias entre os grupos etários foram comparadas e analisadas estatisticamente, sendo utilizado o teste de normalidade Shapiro-Wilk seguido do student t-test e estabelecido como valor de significância estatística um p ≤ 0,05. Resultados: Foi evidenciada diferença estatisticamente significativa quando comparadas as médias do módulo de cisalhamento do tendão supraespinal dos adultos jovens (23,98 ± 9,94 KpA) com a dos idosos (17,92 ± 6,17 KpA). Conclusão: Houve diferença entre as médias do módulo de cisalhamento medido pela elastografia com SSI, demonstrando diminuição significativa do módulo de cisalhamento com a progressão da idade cronológica. Nível de Evidência III, Estudos diagnósticos - Investigação de um exame para diagnóstico.